Sadoun Customer Service & Order Hotline: 1-888-519-9595

+ Reply to Thread
Page 2 of 2
FirstFirst 1 2
Results 11 to 19 of 19

Thread: No signal at all

  1. #11
    New Member Newbie taveechai is on a distinguished road
    Join Date
    Jul 2009

    Posts
    8
    Rep Power
    0

    I checked the signal level, it's 0%

    I asked another person to be in the room to watch the signal (communicated with walkie talkie). It was none, Can it be the receiver problem? If it was your case, what would you do to check to eliminate problems?

  2. #12
    Super Pro Expert pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010's Avatar
    Join Date
    Feb 2004

    Posts
    1,497
    Rep Power
    383
    although doing the walkie talkie thing is possible it makes it very diffilcult to set this up.
    The aiming spot is very small and easy to miss.

    If it was my setup I'd take a small tv and receiver out to the dish and do the adjustments there.

  3. #13
    Senior Member Pro Jim-S is a jewel in the rough Jim-S is a jewel in the rough Jim-S is a jewel in the rough Jim-S's Avatar
    Join Date
    Jun 2007

    Location
    Kent City Mi
    Posts
    625
    Rep Power
    164
    Installing your satellite dish and receiver - DIY INSTALLATION SUPPORT

    Have you viewed this site....
    You don't say if you have a motor or not but you will fine both setups here.
    Mercury II, DG-240, 90cm, QPH-031, DiSEqC or UNL1
    S-DS41C..4X1
    I like to shop at Sadoun Satellite sales.

  4. #14
    Super Pro Expert pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010's Avatar
    Join Date
    Feb 2004

    Posts
    1,497
    Rep Power
    383
    one of his postings had a link to external pic hosting site, and some pictures.

    The install looks good.
    Shows the sat pointing in right direction (like the compass shot!)

    Its a stationary dish - no motor.

  5. #15
    New Member Newbie taveechai is on a distinguished road
    Join Date
    Jul 2009

    Posts
    8
    Rep Power
    0

    thank you guys

    I finally got it working, I bought a new Signal Finder today. It's working now. I appreciated all your helps and efforts. Sorry for the mess, first I thought I could be some other problems.

    By the way, could you recommend a portable TV for me? I will buy one on EBAY for next time installing.

    Thanks so much,
    Now I can sleep.

  6. #16
    Super Pro Expert pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010 has much to be proud of pmb1010's Avatar
    Join Date
    Feb 2004

    Posts
    1,497
    Rep Power
    383
    so what what the issue?

    What fell into place (so we can share with other folks having similar issues!)

  7. #17
    Senior Member Pro Jim-S is a jewel in the rough Jim-S is a jewel in the rough Jim-S is a jewel in the rough Jim-S's Avatar
    Join Date
    Jun 2007

    Location
    Kent City Mi
    Posts
    625
    Rep Power
    164
    You should be able to find a 13'" digital tube type tv for about 100 bucks at most big stores.
    I have to get one someday, right now I use a 25" tube type Tv needless to say it's a bit awkward.

  8. #18
    New Member Newbie taveechai is on a distinguished road
    Join Date
    Jul 2009

    Posts
    8
    Rep Power
    0

    I guess , signal finder was a savior

    After I bought this signal finder, it showed sign of working (Pitch sound) even I connected just one side to the receiver (in the Antenna setup mode). Then I connected other side, it made more sense (the gauge went from 0 to 100). From that point, I went outside and followed direction of signal finder. Turn out I just needed to adjust a little bit more from what I set to get the peak signal. This new position made a peak sound. I locked that position. I then went back to my room, re-scanned the satellites. It just worked. Got signal 66% or more and my day was over.

    I'm happy with the result, thank guys.

  9. #19
    Moon Shiner Expert rainman is a splendid one to behold rainman is a splendid one to behold rainman is a splendid one to behold rainman is a splendid one to behold rainman is a splendid one to behold rainman is a splendid one to behold rainman is a splendid one to behold rainman's Avatar
    Join Date
    Oct 2005

    Location
    Louisa KY
    Posts
    5,103
    Rep Power
    679
    congrats taveechai glad to here you got it going.
    Rainman's Equipment
    Undien 4600,DSR 922, Fortec Ultra, Satworks 3618, Sathawk pvr 800
    2 Fortec Mercury II, Fortec Classic NA, DVB World USB 2104D
    8.5' Orbitron polar C Ku dish, 8.5' Birdview HH C Ku dish
    100cm Fortec dish, 90cm Fortec dish
    2 DG-240 HH motors, Co Rotor II feed horn
    Norsat 8515 C band lnb, Norsat 4506A Ku lnb
    BSC-621-2 Lnbf, Invacom QPH-031 Lnbf
    Invacom SNH-031 Lnbf, Fortec Fsku-v universal Lnbf
    V-Box, G-box

    I Like To Shop at Sadoun Satellite Sales.www.sadoun.com


    Sadoun Satellite Sales
    888-527-9888

+ Reply to Thread
Page 2 of 2
FirstFirst 1 2

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Content Relevant URLs by vBSEO 3.5.0