Wave Frontier Toroidal T-90 Satellite Dish

[satesco]

how strong is 42e for you then?

I pickup almost all turkish transponders with my toroidal!

[Tom0000]

Hey Tom,

how strong is 42e for you then?

I can say, 99% of this what I can find on it if I will move LBNF 4 degrees I am able to receive in current position. 42e is very strong in my city. Only very weak signals not possible to receive using 1m dish I am not able to receive in this configuration. The same I can say about 45e. I do not have to change the mount point of 8w and 45e from standard rail to upper position.

There is the picture of my last configuration with center in ~17e.

[skyman114]

I`m after a little guidance, I have a T90 and am planning on obtaining signal from 16 different satellites. Now my problem lies with the diseqc switching.
I have purchased a "SPAUN SUR420F" and 4x Technomate TM-4s 4x1 switches.

My first question is : In what mode do I use the SUR420F ?

My second question is : I currently have a DM7020 on a 1m motor set up and will be transferring this to the T90. Has anyone got a screen shot from a DM7*** of their satellite set up for a similar 16 lnb system ? The satellites are not important it`s the assignment of lnb`s verse switches i need.

Thanks in advance.

[lumpkin666]

for your setup, you might try the forums as pli-images.org. They were very helpful in helping me figure out how to setup a system with multiple switches and multiple motors on the same setup. My circumstance was that I couldn't do it via the menu system due to the complexity, but they helped me understand how to edit the config files and load them onto the box manually.

[Tom0000]

cPanel® vbmenu_register("postmenu_59443", true




This spaun is not bad. I have it from my old dish. Now I have bought viper 8/1 switch and I am using it with 5x4/1 axings. Is it better from spaun ? I do not know. The same good.

Enigma in your receiver lets you configure not standard configuration or rotor (last position on the list).
Add 16 + commons (like 5W, 10e, ...) to your set, change LNB index for unique for each and in (blue button) configuration set diseqc 1.1 , signal diseqc set to correct for yours 4/1 , uncommited correct for spaun.
That is all.

[skyman114]

Thanks guys i think i have it clear in my mind what i need now.

[arbra]

Hi all,

I read Iceberg's, Satlex and the manufacturer tutorial for my brand new Twin Dish 90 (like Wavefrontier) but i cannot have 2 satelites working at the same time (for instance HB13°E and Astra 19.2E). I use a cheap 8 x 1 switch but i'm not sure my old "unflashed" Kaon 570 receiver can handle Disecq 1.1

The other problem is that i cannot receive Eutelsat W2 10°E nor others satellites exept Sirius. I'm using standard cheap universal Lnb's. Could this be the problem ? If so what do you advise me to buy knowing that I would like to receive satllites between (if possible) HELLAS SAT 39.0E up to AB 3°W as this azimuth range of 42°should normally be ok for a WF.

Many thanks in advance for your help

Patrick

ps : pictures of the installation & receiver menu can be posted

[Muad'Dib]

Get a 10/1 and use it with diseqc 1.2.

[RimaNTSS]

Hi everyone!
I have this dish from 2004 and like it very much. Of course I also like to spend some time tuning it up. Those plastic LNB holders where only 5 coming with antenna and I did not think that it is good idea to buy another ones. So I made some not expensive adjustments to system itself. It gave LNBs possibility to be moved vertically. Antenna holder is also hand made- local welder helped a lot.

[Admin]

BTW, Reversed polarity LNBFs for this dish and T55 can be found here:
DSL2R Sadoun Toroidal Reverse Polarity LNB LNBF Dual Single DSS Standard and Universal