|
|
|||||||
| SatControl Discuss installation, features, and tech support issues on Satcontrol SatTracer Horizon to Horizon motors. |
 |
|
|
LinkBack | Thread Tools | Display Modes |
09-27-2006, 12:42 AM
|
|||
|
|||
|
Delete any motor "software" limits from receiver menu.
What is your location, maybe, 119W is a west limit for your motor? By specs it moves +/- 50 degrees both ways. Check this calculator: http://www.moteck.com/product.asp?idproduct=91 Also, if you see it not moving all the way to ~50 mark on motor shaft scale, try to move using pin button on motor. If it moves with pin buttons, maybe cable is not good: bring receiver close to the motor and check with short cable. Good lucK!
__________________
|
|
09-27-2006, 08:08 AM
|
||||
|
||||
|
it sounds like your limits in the receiver is off like boroda1 said i would check this first.
__________________
Rainman's Equipment Undien 4600,DSR 922 Fortec Ultra, Satworks 3618 2 Fortec Mercury II Fortec Classic NA 8.5' Orbitron polar C Ku dish 8.5' Birdview HH C Ku dish 100cm Fortec dish 90cm Fortec dish 2 DG-240 HH motors Co Rotor II feed horn Norsat 8515 C band lnb Norsat 4506A Ku lnb BSC-621-2 Lnbf Invacom QPH-031 Lnbf Invacom SNH-031 Lnbf Fortec Fsku-v universal Lnbf V-Box I Like To Shop at Sadoun Satellite Sales.www.sadoun.com
|
|
09-27-2006, 02:57 PM
|
|||
|
|||
|
Quote:
 ). You should have 121W echo9 for sure.If you don't get G10R, you can try to attach a second LNBF to the east side of your existing one, and put G10R location as 119W or 120W in receiver's USALS menu and use DISEqC switch built in in SM3D22
__________________
|
|
09-27-2006, 04:03 PM
|
||||
|
||||
|
Are you certain you are properly aligned on true south? If not that will cause your problem also.
__________________
8.5' Mesh Dish w/ C & Ku lnb's & 24" actuator 8.5' Mesh Dish w/ BSC621-2 fixed install for circular C Band on 40.5 Fortec Star 90cm Dish w/ FSKUv lnbf & DMSISG2100 Motorola DSR922 Fortec Mercury II Digital Stream HD1150.
|
|
09-27-2006, 05:20 PM
|
||||
|
||||
|
your true south sat should be amc5 did you start you alignment on this sat?
__________________
Rainman's Equipment Undien 4600,DSR 922 Fortec Ultra, Satworks 3618 2 Fortec Mercury II Fortec Classic NA 8.5' Orbitron polar C Ku dish 8.5' Birdview HH C Ku dish 100cm Fortec dish 90cm Fortec dish 2 DG-240 HH motors Co Rotor II feed horn Norsat 8515 C band lnb Norsat 4506A Ku lnb BSC-621-2 Lnbf Invacom QPH-031 Lnbf Invacom SNH-031 Lnbf Fortec Fsku-v universal Lnbf V-Box I Like To Shop at Sadoun Satellite Sales.www.sadoun.com
|
|
09-27-2006, 10:18 PM
|
||||
|
||||
|
Also another thought. Are you moving beyond 119 just not getting reception or not moving beyond 119?
__________________
8.5' Mesh Dish w/ C & Ku lnb's & 24" actuator 8.5' Mesh Dish w/ BSC621-2 fixed install for circular C Band on 40.5 Fortec Star 90cm Dish w/ FSKUv lnbf & DMSISG2100 Motorola DSR922 Fortec Mercury II Digital Stream HD1150.
|
|
09-29-2006, 04:51 AM
|
|||
|
|||
|
Ok
I got 121...but another question.... the motor only move to 45 degrees either way... Is this normal... tryed removing limits... nothing... numbers on motor goto 60.... thanx for all the help.. guys
|
|
09-29-2006, 01:59 PM
|
||||
|
||||
|
My Sg2100 is advertised at 75 degree of travel from center in either direction. I get 57. Do not know the specs of your particular motor.
__________________
8.5' Mesh Dish w/ C & Ku lnb's & 24" actuator 8.5' Mesh Dish w/ BSC621-2 fixed install for circular C Band on 40.5 Fortec Star 90cm Dish w/ FSKUv lnbf & DMSISG2100 Motorola DSR922 Fortec Mercury II Digital Stream HD1150.
|
|
09-29-2006, 02:10 PM
|
||||
|
||||
|
my stab 100 is 60 degrees either way.
__________________
Rainman's Equipment Undien 4600,DSR 922 Fortec Ultra, Satworks 3618 2 Fortec Mercury II Fortec Classic NA 8.5' Orbitron polar C Ku dish 8.5' Birdview HH C Ku dish 100cm Fortec dish 90cm Fortec dish 2 DG-240 HH motors Co Rotor II feed horn Norsat 8515 C band lnb Norsat 4506A Ku lnb BSC-621-2 Lnbf Invacom QPH-031 Lnbf Invacom SNH-031 Lnbf Fortec Fsku-v universal Lnbf V-Box I Like To Shop at Sadoun Satellite Sales.www.sadoun.com
|
|
09-29-2006, 03:08 PM
|
|||
|
|||
|
Quote:
it was advertised to go 50º each side, but indeed, stopped somewhere at 49º. I am at 37.2N 121.8W and the east limit for my motor is right where AMC5 79ºW is. My solution, as I told already, is to put a second LNB to the left(east) side of existing one: this way you can extend your range for 4 -5 degrees more.
__________________
|
|
09-29-2006, 05:21 PM
|
||||
|
||||
|
cool
 glad to here you got it going.
__________________
Rainman's Equipment Undien 4600,DSR 922 Fortec Ultra, Satworks 3618 2 Fortec Mercury II Fortec Classic NA 8.5' Orbitron polar C Ku dish 8.5' Birdview HH C Ku dish 100cm Fortec dish 90cm Fortec dish 2 DG-240 HH motors Co Rotor II feed horn Norsat 8515 C band lnb Norsat 4506A Ku lnb BSC-621-2 Lnbf Invacom QPH-031 Lnbf Invacom SNH-031 Lnbf Fortec Fsku-v universal Lnbf V-Box I Like To Shop at Sadoun Satellite Sales.www.sadoun.com
|
|
09-29-2006, 06:30 PM
|
|||
|
|||
|
Quote:
Can you tell, please, just for the record, when you press "WEST" button on a motor, when on i't scale the moving stops? Is it still in front of 45° mark or it goes up to 50°? Thanks.
__________________
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
|
sm3d22
Linear Mode
