|
|
|||||||
| Installation Support Post questions about installations issues. |
 |
|
|
LinkBack | Thread Tools | Display Modes |
10-18-2009, 07:11 PM
|
|||
|
|||
Need help converting fc90p to fc90u
I am showing a picture of the bracket for the reflector that i have in the first attached picture it is a fc90p. I am looking for the attachment, replacement brackets for a fc90u to hook to a dg380 motor. Can any one help? The 2nd picture is what i am looking for. That is the reflector brackets, the lnb arm, and the u-bolt bracket that goes to the motor.
Please help! Thanks 
|
|
10-18-2009, 08:59 PM
|
||||
|
||||
|
Have you checked with Sadoun he may be able to help you.
__________________
Rainman's Equipment Undien 4600,DSR 922 Fortec Ultra, Satworks 3618 2 Fortec Mercury II Fortec Classic NA 8.5' Orbitron polar C Ku dish 8.5' Birdview HH C Ku dish 100cm Fortec dish 90cm Fortec dish 2 DG-240 HH motors Co Rotor II feed horn Norsat 8515 C band lnb Norsat 4506A Ku lnb BSC-621-2 Lnbf Invacom QPH-031 Lnbf Invacom SNH-031 Lnbf Fortec Fsku-v universal Lnbf V-Box I Like To Shop at Sadoun Satellite Sales.www.sadoun.com
|
|
10-19-2009, 02:20 AM
|
|||
|
|||
No luck
No luck at sadoun, tried there first. That is unless i am looking in the wrong place. There was no option to buy what i was looking for. The only option was the whole dish. The picture shows way I need the other setup.
Last edited by ASDFLKJ; 10-19-2009 at 02:54 AM.
|
|
10-19-2009, 02:02 PM
|
||||
|
||||
|
Just change the post on the motor...
The easiest thing, and a better install is to just switch out the tube on the motor to a smaller one. Sadoun has it for $13. Check on the HH motor page...
42mm Replacement Tube for PowerTech DG240, DG280, DG280B, DG380 Motors:Use this tube if you are going to use a small dish under 95cm. Should be an easy fix. It is better, because, you see there is a bolt that runs throught the arm and helps fix the direction on the tube. The other mount is just a friction fit.
__________________
VA 39N, 78W, Mercury II, Fortec 31", 36", 72", SG2100, DG-280, H180 (two DSR-922's sitting in a closet and to be the next project) HDTV TV with no pay tv.
|
|
10-22-2009, 02:32 PM
|
||||
|
||||
|
Do you have the pole mount as shown in the photo?
__________________
VA 39N, 78W, Mercury II, Fortec 31", 36", 72", SG2100, DG-280, H180 (two DSR-922's sitting in a closet and to be the next project) HDTV TV with no pay tv.
|
|
10-23-2009, 03:23 AM
|
||||
|
||||
|
Hi,
I think we still have a U-Bolt bracket in stock. It is not listed on the website anymore as we thought we ran out of stock. But we found a few in stock. Call and ask the sales rep to check with warehouse. It is $10 plus s/h
__________________
|
|
10-23-2009, 04:43 PM
|
||||
|
||||
|
Ok, I just noticed from your picture one that you have the newer Fortec 80cm dish not the older one. On this newer one the U-Bolt bracket will not work because the the LNBF Arm is different.
__________________
|
|
10-24-2009, 07:59 AM
|
|||
|
|||
|
Take a look at the first post it explains what i have, and also what i need. The dish that i have is the fortec 90cm and not the 80 cm. It is the newer one, but it will not work with a dg380 motor. That is why i have sent the photos.
|
|
10-26-2009, 04:50 AM
|
||||
|
||||
|
All you need is #12 here: http://sadoun.com/Sat/Order/Motors/HH-Motors.htm
__________________
|
|
11-05-2009, 05:39 PM
|
|||
|
|||
|
What i want to make my dish work for may motor. (dg380)
Have the setup that is in the first picture. What i am looking for is the setup that is in the 2nd picture and that is what i want. The reflector brackets, the lnb arm, and the u-bolt bracket. This is what i want. This is for a fc90 dish.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
