problem install motor SG2100 WITH INVACOM

[le74nguyen@hotmail.com]

Hi: iam just new- i have couple question about install motor SG2100 with invacom- I took 9 hour to install but nothing work- it's have no signal at all. (I use dish 33") I don't know what's i do wrong. the motor sg2100 it's not on- I don't see any power of sg2100. does any person can help me this. I almost carzy. sorry I am just women. may be not good in this. But I hope some body can show me step by step to do it. I am very apprecetiate. please email me le74nguyen@yahoo.com. thanks
I just purchase all the package. it's inlcude dish+motor sg2100+ invacom. again I still not conect to my reciever viewsat ultra. now it's don't have any singal. please help me. thanks

[lumpkin666]

Now that you've had some time to relax, give us some details as to what you're having problems with specifically.

You said that your motor still doesn't have power. Do you mean that the little green light is not lighting up on the motor?

You said that you don't get a signal. Are you using an external signal strength meter to determine this (and if so, do you have the calibration set sensitive enough to indicate a weaker signal)?

You said that you don't have your receiver hooked up yet. If this is correct, how are you trying to power your motor? The motor will not get power unless your receiver is hooked up and active (unless, of course, you are using some power injector device such as the battery pack that comes with some signal meters).

Have you followed the directions for installing the dish/motor/lnb - including setting the proper inclination on your motor (set the inclination using the lattitude scale to set it to the lattitude of your location)?

Maybe tell us your location, what your current elevation settings on your motor and dish are, and where you are currently pointing your dish, and maybe someone can see an issue with your setup or recommend some possible solutions. Also, it might be worth letting us know which output on your inviacom lnbf you are using. If you are using the circular side and pointing at a linear satellite, you're not going to have much luck.

Don't dispair. These signals are pretty tough to lock in on your first time. There are a lot of variables that are can be difficult to understand for a beginner. Also, be aware that even if you have everything configured 100% the way that the instructions tell you, you still may need to do some fine tuning since inclination markings can be off slightly, and most numbers you'll get online are only estimates for your area.

[reho33]

One of the "tricks" that I used was this:
Hook up motor to receiver
Go into setup for receiver
Setup Echo 6 and 8 (110) for USALS with your lat and long
When finished, have the receiver "move" the motor to the above
Setup motor on pole or bracket
Keeping the motor elevation/latitude the SAME ONLY move the dish up or down and the motor/dish ass'y side to side until you get a signal.
Tighten everything at this point.
The whole point of this exercise is to use the high power DBS sat to "find" your place on the arc. You could certainly use like AMC3 or SBS6 but they are a lot harder to "peak" on because of the power level.
While using this method may not be for everyone, it has saved me a lot of time to "rough set" the dish settings before fine tuning.

[le74nguyen@hotmail.com]

I live in ca- perris.

[le74nguyen@hotmail.com]

now I have a problem to set up invacom- on it have 2c+ 2L- I connect 1c+ 1L go to swic 4x4- 1 out go to lnb of invacom. but I don't see any signal.- do I any wrong? one thing I don't know how to set up receiver to diseqc 1.2..need help please. thank you.......linda

[rainman]

Originally Posted by le74nguyen@hotmail.com

now I have a problem to set up invacom- on it have 2c+ 2L- I connect 1c+ 1L go to swic 4x4- 1 out go to lnb of invacom. but I don't see any signal.- do I any wrong? one thing I don't know how to set up receiver to diseqc 1.2..need help please. thank you.......linda

if you could give us your zip code we can figure you latitude and longitude
also your motor angles and dish angles that way we can get you started on finding your true south sat and get you aligned.

[le74nguyen@hotmail.com]

one more problem-I install the brack dis+ motor+ invacom done. but problem is singal no stay.. what's wrong? do I done wrong? why's happen above- sorry- last time i forgot give descrble-- but I lived in ca-perris-92571. help please.. thank you!!! linda

[rainman]

Ok Linda lets get started first use the receiver and reference the motor set it to zero use a compass and see if assembly is pointing at 166 degrees on the compass if not move the motor on the pole to point in this direction. then set the sg2100 on the latitude scale to 34. then set the dish on the dish scale set it to 25 degrees. now select antenna setup in your receiver and select satellite sat mex 5 set the lnb to standard 10750 set lnb power on set positioner to usuals set TP freq to 12028 horizontal set sr to 3255. now we are ready to look for signal. should have the receiver and small tv set up at dish so you can see any changes in signal. move the dish to sat mex 5 with usuals then slowly move the motor and dish assembly on the pole east or west to find max signal you should mark the pole before you start moving so you can return to your starting point. move 1/16th of a inch and aloww 15 seconds for the receiver to see the change continue along this path till you find a signal if no signal is found raise or lower dish elevation by 1 degree and try east and west movement again continue to find and lock the highest signal. the key to thus is slow small movements.good luck on your adventure. one more thing make sure you have the coax on your lnb hooked to a L port.

[le74nguyen@hotmail.com]

now set up done but the signal and quality is not stay- it's come and lost-doI do something wrong? help please!!! lady maybe do slow. thank you!!!

[le74nguyen@hotmail.com]

my langitude:117.2 East ot west?
when I go to USALS manual for type latitude + longitude- but I don't know my longitude east or west- please help me. thanks
I can not belvied it's hard to setup sg2100 + invacom like that!! I lost two week to set up but still not watch tv.- when purchase all this, I though it's easy but it's different-I did tried too many way to find out how to get a singnal but until now I still got stuk on it. please help me- I am very appreciated. thank you!

[le74nguyen@hotmail.com]

why I check verything- but on the screen show "RANGE OVER FLOW CHECK UR POSITION" ---what's happen? why is happen like above? what's i do wrong? help me pleas!!!! thanks

[DougRuss]

Think you have your Longitude set to EAST....should be WEST. Give that a try !!

And North for your Latitude..........

[le74nguyen@hotmail.com]

so how to change logitude to west? can you help? thanks

[DougRuss]

Originally Posted by le74nguyen@hotmail.com

so how to change logitude to west? can you help? thanks

Hope I can explain this well?

..................

On the Remote,Press "MENU"
Then Click On "Installation"
now Click On "Antenna Setup"
Scroll Down to" Motor"
and use the Right Arrow Button on Remote until you see "USALS".
Now Click "OK"

There you will see your Longitude/Latitude Menu.

Use the Right Arrow Button on Remote.
The Longitude setting will disappear.............
Now using the Number Buttons on Remote....enter your Longitude number.

Then use the Down Button on Remote. It will enter West (W) along side the number.
Now Click "OK" on Remote.
Hit "Exit" on Remote...Click "YES" to Save.
And Exit again.

..........

[le74nguyen@hotmail.com]

thank you, I did it, but still can not find a signal- can you help? I did follow step by step you show me but I still not find any signal... need help please..........

[elgemcdlf]

Back to relax First how do you have everything connected?

[le74nguyen@hotmail.com]

yes- I did conect everything- I did check it for make sure is everything correct- now Iam very sure I did connect everything-- I tried a best i can but until now I cannot find any quality- "first I use the receiver and reference the motor set it to zero use a compass and see if assembly is pointing at 166 degrees on the compass. then I set up the motor on the latitude scale to 34. then set the dish on the dish scale set it to 25 degrees- I select antenna setup in receiver and select satellite the lnb to standard 10750 set lnb power on set positioner to usuals set TP freq to 12250- afterthat I looking a signal- I move dish up/down/east/west to find signal but don't see anything- again I did connect coax cable to lnb between receiver and motor,done. Now still don't find any quality yet.. the quality is zero.. but S..have 55%-- I don't know what I do wrong? please anybody have some thing happen like me above... please show me how to do it. I am very appericeate.. thanks

[le74nguyen@hotmail.com]

the signal is can not find it- I take everything out and install again- i hope this time can work out0- but any person have experience about install Motor Sg2100+ invacom. please help me or share with me any your experience... I always waiting to your help.. thanks

[wejones]

Originally Posted by le74nguyen@hotmail.com

y... I select antenna setup in receiver and select satellite the lnb to standard 10750 set lnb power on set positioner to usuals set TP freq to 12250- afterthat I looking a signal- I move dish up/down/east/west to find signal but don't see anything- ....

Maybe I'm missing something, but what are you trying to find on 12250???