ultra and stabHH120 problem

[bundo]

hi just installed the ulra got 75 signel on Diseqc#1 position setting i have 1.2 for motor FTA lnb uneversal1 22khz- LNB On lnb 10600mhz now on the other lnb is dish standard lnb 11250 22khz on and its on diseqc#2 lnb power on tp 12224v20.000 position disable fta dont care about dish. my concern is my motor not moving i did power scan on different satellites now i got 900 FTA channels the same from IA 5 i called 2 times for help no response back its driving me nuts anyone knows please tell me what to do thank you telestar 5 i got channels moter problem i got stab hh120 36"fortecstar uneversal LNB . i go to antenna setup i click G10Rku i tried all my setting i onley do is change Diseqc to #1 and position setting 1.2 thats all click ok 0 channels then i power scan i get same channels from IA5 thats how i got 900 same FTA or more please help thank you and god bless

[dtsexpert]

Make sure your dish tracks the arc correctly before mount the circular lnbf next the the linear one. It's very important to make the dish track to arc right . Once you know dish tracks the arc OK, then deal with the switch later.
Suggestion for using Diseqc 1.0/2.0 with Diseqc 1.2:
1. Make sure you set the port correctly.
2. 22khz has no affect with the your current set up, so it's not important.
3. Set the LOF correctly for both linear an circular lnbf.
4. Make sure you pick active freq when find sats. DishNet has some "spot" transponders which the the signal only covers some certain area. Check lyngsat.com for more info on DN transponders.
5. Diseqc switch must be installed between lnbfs and Stab motor.
How well does your dish tracks the arc?
Michael

Originally Posted by bundo

hi just installed the ulra got 75 signel on Diseqc#1 position setting i have 1.2 for motor FTA lnb uneversal1 22khz- LNB On lnb 10600mhz now on the other lnb is dish standard lnb 11250 22khz on and its on diseqc#2 lnb power on tp 12224v20.000 position disable fta dont care about dish. my concern is my motor not moving i did power scan on different satellites now i got 900 FTA channels the same from IA 5 i called 2 times for help no response back its driving me nuts anyone knows please tell me what to do thank you telestar 5 i got channels moter problem i got stab hh120 36"fortecstar uneversal LNB

[bundo]

this is my set up on IA/5Ku> 75 signel (lnb type uneversal1 lnb freq 9750/10600 22KHz- Diseqc#1 lnb on tp 11749v7232 positioner Setting 1.2 satellite scan FTA . ----> but my DiSEqC is not in between the lnb and the motor this could be the problem i hope thats all. do i need to set anything different on the antenna setup thank you so much for your reply god bless you

[bundo]

thank you for your help got motor going. so far got 12 birds . im at 80.2W and 25.7N how far can i go towards atlantic birds thank you
my setting was true south first bird for set up was IA5 ?

[dtsexpert]

No, your true south is AMC5 at 79W. Check out the link below for instruction of how to set up h-h mount correctly:
http://www.sadoun.com/Sat/Installati...stallation.htm
Michael

Originally Posted by bundo

thank you for your help got motor going. so far got 12 birds . im at 80.2W and 25.7N how far can i go towards atlantic birds thank you
my setting was true south first bird for set up was IA5 ?

[bundo]

ty for your help. my 36'' has an uneversal LNB if i strap on to it 1 standard lnb would it work to recieve other birds that have standard or is there a dual lnb such as standard and uneversal maybe its a stupid question but doesnt hurt to ask thanks.

[bundo]

ty for your help. my 36''stabhh120 has an uneversal LNB if i strap on to it 1 standard lnb would it work to recieve other birds that have standard or is there a dual lnb such as standard and uneversal maybe , and what angle or position?