Fortec Mercury II >>> DYNAMIC

[Sadoun]

Fortec Mercury II receiver is now replaced by Fortec DYNAMIC. This new receiver is exactly the same as MERCURY II except, it has a different faceplate.



DYNAMIC will be available within a few days from our store.

[branson]

my position is 37.6 n 122.4 w need some help with the dynamic system
try to get signal from 97w and 123w but no luck,
system info

fortec dynamic
90 cm dish
dg280 motor
swicth 4 port
qph-031

need some help, i just got 110 w but i want to get signal from 97 and 123

thank

[Vitruvius]

For the other satellites you need to use the standard linear outputs from that LNB. C = circular and L = Linear.
I am pretty sure you need to set the LNB type to 10250 for linear in each satellite that you are searching. Most all the the FTA sats are linear. If you look at 110, it is probably set to 11250 which is for circular and you get that reception. You also need to set your switch to the corresponding LNB number for each satellite.

Good luck

[Jim-S]

Originally Posted by Vitruvius

For the other satellites you need to use the standard linear outputs from that LNB. C = circular and L = Linear.
I am pretty sure you need to set the LNB type to 10250 for linear in each satellite that you are searching. Most all the the FTA sats are linear. If you look at 110, it is probably set to 11250 which is for circular and you get that reception. You also need to set your switch to the corresponding LNB number for each satellite.

Good luck

That would be 10750 for "L" and "C" is 11250. Just trying to keep everyone on the ball.........hummm

[branson]

thank all, i am going to try and see what happen, and do a blind scan on 97 w thank again.

[branson]

hello again i notice that my longitud has a negative value like -122.4 how can i set up a negative value in the popup menu of usals where you set your latitud and longitud. because just accept a positive value, i checked with dispointer and it is negative. my question is if i have an negative value in my longitud in my system setup will be positive?

[Vitruvius]

I don't think you should use a negative value. You would be either E or W.

[Jim-S]

Why can't we find this on the Fortec Web site. The Dynamic

[branson]

hello again this is about this formula elevation=p-(45-Latitud) so, for example p = to value for fixed disk if i have to setup the aligment on my motorized dish, i set the latitud on the motor but on the dish declination angle i will have to apply the equation for each satellite.

thank again.

[Jim-S]

http://www.sadoun.com/Sat/Installati...ns-Dynamic.pdf



How to install an HH Mount DiSEqC USALS Motor? Applies to DG280, DG280B, DG380, STAB HH100, HH120, Moteck SG2100


Read these two articles and watch the video.......it's very helpful.
Jim

[branson]

i hit 97w galaxy 25 but i have only 25-29 q i try to adjusted and still the
same do i need another dish a 120cm, or a diferent lnb my is aviacom i buy the system from sadoun i don't know what to do know i can not increase my quality signal need help

[Jim-S]

Originally Posted by branson

i hit 97w galaxy 25 but i have only 25-29 q i try to adjusted and still the
same do i need another dish a 120cm, or a diferent lnb my is aviacom i buy the system from sadoun i don't know what to do know i can not increase my quality signal need help

Please verify what satellite you are on.
97w is Galaxy 19, and Galaxy 25 is 93.1w
Use www.Lyngsat.com to check.
Your dish is fine, do you have a sat. meter, you can fine tune the satellite in with it by moving the dish up and down, side to side, very very same amounts. I did this with mine it will enable you get good quality sig. You also can use the sig button on you remote to view the quality , which you are probably doing. I think all you have to do is a little tweeking.
If you have your switch inline try without it. Check all your connections, and what is your coax, is it good quality, and how long is it.

[branson]

the satelite is galaxy19 97w i have a swith and a sat finder the sat finder show 9 1/2 db every time tha i move the dish side to side i lost the signal
and also i have signal amp for longer cables the cable is new i have a diseq 1.0 switch and a s-sm21h, i have video in amc 4 but no audio ,galaxy 25 audio and video, echo 119 video and audio, 123 w nothing

[Jim-S]

When you have your signal on your sat finder move your dishup or down slightly, this also will help tune in the signal.