Results 1 to 5 of 5

Thread: Just got a dish 1000+

          
   
  1. #1
    Ong Tu's Avatar
    Ong Tu is offline New Member Newbie
    Join Date
    Mar 2006
    Posts
    19
    Rep Power
    0

    Just got a dish 1000+

    Just got a dish 1000+ I set up a few dishes in my time so that is not a problem.
    When I set everything up I could only get 110 but set it up to get signal for 119 at port #1 (2D) from lnbf. Assuming it was my Dish setting went to adjust dish after this was done I could not get a signal from any sat. Tried everything and still no luck have a very good signal from the LNB but nothing on my receiver. Now I’m wondering if there is a problem with the 44 Switch or the Power Inserter and power supply. The receiver is good also have good signal strength from LNB. Any help would be appreciated thanks.



    Dish Network Dish 1000+
    Dish Pro Plus-44 Switch
    The Power Inserter and power supply


    On My DPP 44
    119- Port 1
    110- Port 2
    118- Port 3
    129- Port 4
    ____________________________________________

  2. #2
    Ong Tu's Avatar
    Ong Tu is offline New Member Newbie
    Join Date
    Mar 2006
    Posts
    19
    Rep Power
    0
    O.K. screwed up on Sat. location lol! But back at square one only have 110 can not get 119!

  3. #3
    pictureon's Avatar
    pictureon is offline Pro Member Pro
    Join Date
    Mar 2004
    Location
    Sacramento CA. Bay Area
    Posts
    512
    Rep Power
    389
    Get signal on 110 and do a check switch After that turn your receiver off with the remote to allow it to get the update. In about 2 hours run the check switch again. Most of the Dishnetwork receivers do not recognize the new dishes or switches before getting the update.

    Good luck

  4. #4
    Ong Tu's Avatar
    Ong Tu is offline New Member Newbie
    Join Date
    Mar 2006
    Posts
    19
    Rep Power
    0
    Thanks that worked---



    Quote Originally Posted by pictureon View Post
    Get signal on 110 and do a check switch After that turn your receiver off with the remote to allow it to get the update. In about 2 hours run the check switch again. Most of the Dishnetwork receivers do not recognize the new dishes or switches before getting the update.

    Good luck

  5. #5
    bigj91 is offline New Member Newbie
    Join Date
    Aug 2007
    Posts
    1
    Rep Power
    0
    Well I've searched and read much as I can , hope this is not redundant, I have a type 1 superdish 121 with a DP34 switch hooked up to a 510, got a 118 repoint-kit from dish part #148328. I mounted the kit, did a hard reset on the 510, after that did check switch, 119,110 pulling signals in the 90/100s, but when i switch to 118, no signals on TP 2 or 18, I am in zip 36701. any suggestions? thx

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 2
    Last Post: 02-15-2010, 02:45 PM
  2. Is the dish 1000+ same size as 1000.2?
    By polariswarrior in forum Dish Network
    Replies: 0
    Last Post: 01-01-2009, 09:50 PM
  3. Larger dish + Dish LNBFs (also comments on dish 1000)
    By PhilipPeake in forum Dish Network
    Replies: 5
    Last Post: 10-26-2006, 06:46 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •