DSR922, PANSAT3500,C-Band,INVACOMQPH031

[gherrm]

I want to feed C-Band to 922 and 3500. And KU Linear & Circular to 3500. And Linear KU to 922. How do I do it. Thank You ! DSR922, Pansat3500SD, C-Band 10'dish C Only Windguard 30"dish, INVACOM QPH031, Sg2100 Motor.

[elgemcdlf]

Ok you will need a 4x DiSeqC switch for the FTA receiver and two splitters with dc pass on one leg. Split your C band coax and connect one of the two to the 922 and the other to a port on the DiSeqC switch. Do the same with the linear Ku coax. Run the circular coax into another port on the DiSeqC switch. Now the out of the DiSeqC switch goes to the FTA receiver.

You have just successfully connected C and Ku linear to your 922 and C, Ku linear and Ku circular to your FTA receiver.

The DiSeqC switch should be placed between the motor and the lnb of the small dish. I would also recommend inline amps for all lines placed as close to the lnb as practical.

Steve

[Sadoun]

Here is a link to some more information:
http://sadoun.com/Sat/Products/Acces.../Bud-slave.htm

[gherrm]

Thank You ! Can I do it somehow with INVACOMQPH031 A B C D into DiSeqC at dish one line into house then split up to the two Recevers.

[Sadoun]

No, you will need two Diseqc switches

L & C to one receiver
L & C to the second receiver

[gherrm]

So it still means I need two RG6 lines coming into house. Thank You !

[elgemcdlf]

FYI to Sadoun. The DSR922 has a seperate input for C and Ku. Not like the single input on the FTA receivers.

Unless someone knows of a different way you will require 3 lines coming into the house. The single feed line for the FTA receiver and a line for C band and one for Ku that go to the DSR922

[Sadoun]

Two lines should be enough. The C & KU lines will go through Hi Freq Splitters and then continue to the 922 receiver. The two extra lines coming out of the splitters go to the DiSEqC switch and into the FTA receiver. You can add a 22KHz switch into the mix as well to connect the QPH

[elgemcdlf]

Sadoun,
Can you clarify. I am counting 4 lines. One C and one Ku from the big dish. One Ku linear and one Ku circular from the small dish. I see tieing the Circ and Linear along with a split leg of C band running into 3 ports of a DiSeqC leaving one out which is the FTA feed. I see a C and Ku from the big dish going to the 922. I count 3. Are you tieing the C and Ku for the 922 together into one line and then splitting again after inside the residence? Perhaps there is only s single Ku feed from the small dish and the big dish is only C band but even then I would split before the DiSeqC which would still leave me with 3 going into the residence. The 922 has no way to switch a DiSeqC or 22 Mhz to my knowledge.

This is positioning the DISeqC between the motor and LNB on the small dish.

TIA
Steve

[gherrm]

No The Big Dsh is C-Only The Small Windgauard has INVACOMQPH031 KU Only
2 Lin. and 2 Cir. feed's on it.

[elgemcdlf]

Alters nothing unless there is a way to tie the C and Ku together and break them apart again. The 922 requires a seperate line for C and a seperate line for Ku. The FTA receiver requires a single line in. This makes 3 lines. The C, Ku linear and Ku Circular can be grouped into one line with a DiSeqC switch which the FTA receiver controls. Instead of splitting the Ku linear line simply hook up to the other port on the lnb. The C band line would have to be split in my mind prior to the DiSeqC. I am going to look at the link Sadoun provided.

Steve

[gherrm]

I think I am going to have to run two lines the C-Band dish is 75' from house and I think I am going to mount small dish on roof. That seems the best way to do it. Thank You All for Your reply"s

[elgemcdlf]

Keep me posted on the progress. I still count 3 lines going into the house. I would like to hear how you did this setup utilizing less. That is if you are running C and Ku linear at the 922 and C, Ku linear and Ku Circular at the FTA

Steve

[gherrm]

Yes there would be three lines.One from C-Band. Two Cir.one Lin.From Small KU dish into Diseqc switch and One line Lin.From Small KU dish into 922 KU spot.

[kyzursozay]

Originally Posted by Sadoun

Here is a link to some more information:
http://sadoun.com/Sat/Products/Acces.../Bud-slave.htm

Wonder if you could clarify ,the link above shows splitter's one port pass , but post above says to use splitters with dc pass on both leg's? I have 36" dish ,hh90mtr,QPH-031lnb w / 22khz 2X1 switch between motor & lnb w/single coax running from mtr. to VS Plat. DVB & 10' C/Ku Astroel RP3 feedhorn running separate C & Ku coax feed's to 922 . So I split C&Ku w/ one port pass to 922, other's to 4X1 diseqC port's 3&4. Then I ran single coax from QPH mtr to port 1 and out port to DVB. Will this work? What would be proper switch settings. Thank's

[elgemcdlf]

Originally Posted by kyzursozay

Wonder if you could clarify ,the link above shows splitter's one port pass , but post above says to use splitters with dc pass on both leg's? I have 36" dish ,hh90mtr,QPH-031lnb w / 22khz 2X1 switch between motor & lnb w/single coax running from mtr. to VS Plat. DVB & 10' C/Ku Astroel RP3 feedhorn running separate C & Ku coax feed's to 922 . So I split C&Ku w/ one port pass to 922, other's to 4X1 diseqC port's 3&4. Then I ran single coax from QPH mtr to port 1 and out port to DVB. Will this work? What would be proper switch settings. Thank's

If I understand what you have done it will not work for long. As I am reading this your DiSeqC switch is located between the receiver and motor? This will burn out the DiSeqC. As to dual DC Pass splitters. Should have read single pass.